Epoxy Floor Still Soft or Sticky After 24 Hours: What Went Wrong

An epoxy floor that is still soft or sticky after 24 hours has one of five problems: the wrong mix ratio, incomplete mixing, a slab below 60°F, a coat applied thicker than the product allows, or Part A that went unstirred before Part B went in. Only the cold one gets better with time: bring the slab to 70°F and wait 48 hr. If the ratio or the mixing was wrong, the soft spots stay soft and have to come out.

At 70°F, B-707 High Build Epoxy takes foot traffic in 12 to 14 hr, so at 24 hr a thumbnail should leave no mark. Full hardness takes 2 to 7 days; firm but not rock hard at 24 hr is normal.

Which problem you have

What you see Cause Will it cure
Whole floor evenly soft or tacky, garage under 60°F Cold slab Yes, with heat and time
Random soft patches, streaks or swirls; the rest is hard Under-mixed batch, or Part A left settled No
One batch area soft, the next hard Wrong ratio on that batch, usually a split kit measured by eye No
Topcoat gummy, wrinkled or bubbled T-444X over 12 mils wet, or T-521/T-520 over 5 mils wet Sometimes with time; usually a recoat
Hard underneath, greasy or waxy film on top Amine blush from a cool, damp cure Yes, wash and sand

Blush is covered in cloudy, hazy or milky topcoat over epoxy.

The five causes

  1. Wrong ratio. B-707 and B-181 are 2:1 by volume. B-933 polyurea is 4:1, and the catalog says to mix it exactly. Every kit is packaged in its ratio, so the ratio goes wrong when a kit is split by eye. Extra Part B leaves unreacted hardener that stays soft for good.
  2. Incomplete mixing. Resin clings to the sides and bottom of the bucket. Pour without scraping and those streaks land on the floor, where they never harden.
  3. Cold slab. B-707 applies at 60 to 90°F on the slab. Below 60°F the reaction slows and the film stays soft for days; well below it, the reaction stalls. A slab on grade in fall sits colder than the air above it, so read a thermometer on the floor. B-181 cold-weather epoxy cures down to 45°F.
  4. Too thick for the product. B-707 is a one-coat high-build product, 3 gal per 350 sq ft at about 14 mils. The topcoats are thin coats: T-444X bubbles and stays soft above 12 mils wet; T-521 and T-520 are 3 to 5 mils wet and the catalog says to go no thicker, because the water in a thick coat cannot leave.
  5. Part A left unstirred. Pigment and solids settle in the can. Pour Part B into unstirred Part A and the top of the mix is off-ratio one way and the bottom the other.

What to do now

If the slab is cold

Heat the garage until a thermometer on the slab reads 70°F and hold it there for 48 hr with the door closed. Then press a thumbnail into the coating. Hard means the cure finished; sand dull and topcoat. Still soft means the problem was the mix.

If the ratio or the mixing was wrong

Soft epoxy stays soft under anything you put over it, so it has to come out.

  1. Scrape the gummy material up with a floor scraper into a bucket for disposal under your town's hazardous waste rules.
  2. Wipe the residue with denatured alcohol on clean rags and let it flash off.
  3. Grind the area to bare concrete with a hand grinder and a diamond cup wheel, and feather the edge of the surrounding hard coating. Vacuum twice.
  4. Recoat with a fresh full kit of B-707, 2:1, mixed for 5 minutes and remixed in a second bucket, in the matching color. A 0.75 gal kit covers 85 sq ft; a 1.5 gal kit covers 175.
  5. Topcoat the whole floor so the sheen matches.

If the topcoat is the soft layer

Give it 48 hr at 60 to 90°F with air moving. Still gummy: scrape or sand it off down to the hard base coat, sand the base coat dull, and roll a new topcoat thin from a tray, T-521 at 3 to 5 mils wet or T-444X at 5 to 12.

How to prevent it on the next coat

  1. Mix full kits. A 3 gal kit of B-707 is 2 gal of Part A and 1 gal of Part B. Use the whole of each can.
  2. If you have to split a kit, measure by volume in marked buckets. B-707 is 2:1 by volume but 12 lb of A to 4.15 lb of B by weight, so a kitchen scale set to 2:1 gets it wrong.
  3. Stir Part A on its own first until the pigment is uniform.
  4. Pour Part B into Part A and mix with the wand on a drill for 5 minutes at low speed, wand below the surface, scraping the sides and bottom. Pour the mix into a second clean bucket and mix 1 minute more; the B-707 data sheet calls for a transfer pail and remix, because unmixed material clings to the first bucket's walls.
  5. Use a fresh bucket for each batch and pour it out as soon as it is mixed. Under 60°F on the slab, switch to B-181 or heat the space for a day before you start.

The full day-one procedure is in how to epoxy a garage floor; the cure stages are in how long 2-part epoxy takes to dry.

Numbers

  • B-707: 2:1 by volume, tack free 5 to 8 hr, foot traffic 12 to 14 hr, full cure 2 to 7 days, 60 to 90°F. B-181: 45 to 90°F. B-933: 4:1 exact, 40 to 90°F.
  • Prices as of November 2026: B-707 0.75 gal kit $106.99, 1.5 gal kit $187.99, 3 gal kit $349.99; B-181 3 gal kit $279.99; mix bucket $9.99; mix wand $9.99. Data sheets: technical documents.

Common questions

Will sticky epoxy eventually cure?

Only if the cause is cold. Bring the slab to 70°F and give it 48 hr. If the ratio was wrong or the batch was under-mixed, the soft spots stay soft and have to be removed.

Does adding more hardener make epoxy cure faster?

No. Extra Part B leaves unreacted hardener in the film, which stays soft and sticky. B-707 is 2:1 by volume, exact, and the kits are packaged in that ratio.

How do I remove uncured epoxy from a floor?

Scrape the soft material up with a floor scraper, wipe the residue with denatured alcohol, grind the area to concrete and feather the edge of the hard coating, then recoat with a fresh full kit.

Cold garage this season: B-181 Quick Set High Build Epoxy, Cold Weather. A floor that is soft right now: call (877) 703-7699, Monday to Saturday, 8am to 6pm ET, with a photo.

Back to blog