Fisheyes and Craters in Epoxy: What Causes Them and How to Repair
Fisheyes in an epoxy floor are repaired after the coat cures: sand the craters flat, wipe the area with denatured alcohol on a clean rag, and roll a fresh coat of the same product. The cause is contamination on the slab or in the coating, usually silicone from tire shine or spray lubricants, or oil, wax, a form release agent or a curing compound. The wet epoxy pulls back from the spot and leaves a round crater with a raised rim and a dark or thin center.
How to tell a fisheye from an outgassing bubble
| Fisheye | Outgassing bubble | |
|---|---|---|
| Shape | Round crater, raised rim, coating pulled back to a thin film or bare slab | Dome or pinhole, coating intact around it |
| Where | Clustered where something was sprayed, dripped or tracked: the parking spot, under the shelf where the sprays sat, in a roller-width line | Spread over porous areas, worse in the sunny half |
| When | The moment the coat is spread | Over the first hour as the slab warms |
| Back-roll | Opens again | Breaks and heals |
If yours are bubbles, read bubbles and pinholes in a new epoxy floor.
Where the contamination comes from
- Silicone. Tire shine, spray lubricants, waxes and vinyl protectants carry it, and overspray settles on the floor as a mist you cannot see.
- Oil and grease. Drips from cars and mowers. A stain that comes back a day after degreasing means the oil is in the slab.
- Form release agents, curing compounds and sealers on newer concrete. Water beads on the surface instead of soaking in. They have to be ground off; acid cannot get through them. See grinding vs acid etching concrete.
- The tools. A roller cover that sat open on a shop shelf, a reused bucket, a squeegee wiped with a rag that had touched silicone.
- Air compressors. The exhaust carries oil mist; a compressor running while the floor is wet can fisheye a whole bay.
How to repair a floor with fisheyes
Inside the working time
Roll more mixed epoxy over the spot once. If it flows in and stays, keep going. If the crater opens again, leave it; chasing it after the coat starts to gel adds roller marks.
After the coat has cured
- Wait for the coat to harden. B-707 recoats in 8 to 12 hr. Past 48 hr, sand the whole floor dull before the next coat.
- Sand each crater and a 6 inch ring around it until the rim is gone and the surface is dull.
- Vacuum twice. Wipe with denatured alcohol on a clean rag, turning the rag often. A dirty rag spreads silicone across the floor.
- Test first. Mix a small amount of B-707 and roll a hand-sized patch over the worst crater. If it fisheyes again, the contamination is in the slab. Grind that spot to bare concrete. Oil: prime the spot with P-820 Oil Stop Primer (cannot ship to CA, CO, CT, DE, MD, MI, NY, OH, RI or UT). Silicone: grind until a test patch holds.
- Recoat. Roll B-707 in the matching color over the sanded area, feathered into the surrounding coat. A 0.75 gal kit covers 85 sq ft. Fisheyes in the topcoat alone get the same sand and wipe, then T-521 at 3 to 5 mils wet or T-444X at 5 to 12 mils wet.
- Topcoat the whole bay so the sheen matches. A patch in the topcoat shows under garage lighting.
How to keep fisheyes off the next floor
- Degrease first, grind second. Scrub oil spots with degreaser and a stiff brush, rinse, and let the floor dry before grinding, so the grinder cuts clean concrete. Grind the whole floor to a 120-grit feel. Spots that darken again the next day get P-820 before the base coat. See how to prep a garage floor for epoxy.
- Clear the silicone out 48 hr ahead. Take tire shine, spray lubricants, waxes and protectants out of the garage, skip them on the cars in the driveway while the door is open, and keep them out until the topcoat has cured.
- Vacuum twice after grinding and keep foot traffic off the bare slab. Shoes track oil in from the driveway.
- Shut the compressor off and keep gas engines out from grinding day until the topcoat cures.
- Open fresh tools: a new roller cover for each coat, a new mixing bucket for each batch, a clean squeegee blade. The catalog says cured residue in a reused bucket ruins the next mix.
- Step into the spiked shoes from a clean spot and wear them only in wet epoxy.
Numbers
- B-707: 2:1 by volume, about 115 sq ft per gallon at 14 mils, working time 30 to 50 min per 1.5 gal batch at 70°F, recoat 8 to 12 hr, 60 to 90°F.
- P-820: 1:1, 200 to 320 sq ft per gallon at 5 to 8 mils wet, recoat 4 to 8 hr, 55 to 90°F. Solvent-based; ventilate.
- Prices as of November 2026: B-707 0.75 gal kit $106.99; P-820 1 gal kit $99.99; 18 inch roller cover $9.99; mix bucket $9.99. Data sheets: technical documents.
Common questions
What causes fisheyes in epoxy?
Contamination on the concrete or in the coating. Silicone from tire shine and spray lubricants is the usual one, then oil, wax, form release agents and curing compounds. The epoxy pulls away from the spot and leaves a round crater.
How do I tell fisheyes from bubbles?
A fisheye is a crater with a raised rim and a dark or thin center, usually in a cluster where something was sprayed or dripped. A bubble is a dome or pinhole scattered over porous areas that breaks when you back-roll it.
Can I roll more epoxy over a fisheye while it is wet?
Once, inside the working time. If the spot opens again, stop. The contamination is on the slab, and the fix is a sand, solvent wipe and recoat after cure.
How long should I keep silicone products out of the garage before coating?
Take tire shine, spray lubricants and waxes out 48 hr before you coat and keep them out until the topcoat has cured.
Oil in the slab: P-820 Oil Stop Primer. A floor that already cratered: (877) 703-7699, Monday to Saturday, 8am to 6pm ET.
